Ceramik Ultra C2TE is a cement adhesive with improved adhesion parameters, created on the basis of cement, a mixture of appropriately selected aggregates and polymer powders. The adhesive also has reduced flow and extended open time.
Depending on where the glue will be applied - on vertical or horizontal surfaces - we can adjust its gel consistency to the needs of the substrate by using different amounts of water.
The glue also owes its unique properties to the use of modern technology. Water in contact with minerals of this type is absorbed in the structure of the fresh adhesive mortar, which allows for full hydration of the cement, regardless of the type of glued cladding, and for the expansion of the application conditions to a temperature of 30°C.
- new technology,
- cement glue with improved parameters,
- glue has limited flow,
- extended open time,
- highly flexible compensates for deformations of the substrate,
- plastic, easy to process,
- for indoor and outdoor use,
- for all ceramic coverings,
- adhesive layer thickness from 2 mm to 15 mm,
IMPORTANT INFORMATION:
- Mixing proportions: 7.0 L to 8.0 L of water / 25 kg,
- Adhesive layer thickness (minimum - maximum): 2 mm-15 mm thin and medium layers,
- Application temperature: +5°C to +30°C,
- Waterproof: YES,
- Frost resistance: YES,
- Grouting: after 12 hours,
- Open time: 30 minutes,
- For use: outdoor / indoor,
- Shelf life: 12 months,
APPLICATION:
Ceramik Ultra C2TE is perfect for installation on difficult cement and gypsum substrates exposed to unfavorable operating conditions. The product can be used in residential and industrial construction:
- For walls and floors,
- For use under floor and wall heating,
- For gluing stone tiles that are not sensitive to discoloration,
- For leveling mineral substrates up to 15 mm thick,
- In residential, public and industrial buildings, garages, health care facilities,
- For absorbent and non-absorbent ceramic coverings: tiles, terracotta, stoneware, ceramic mosaic, clinker, brick tiles, stoneware, etc.
- For use on deformable and non-deformable substrates, such as monolithic concrete, cement, lime-cement, lime and gypsum plasters, cement and anhydrite screeds and screeds, terrazzo, plasterboards, fiber-cement boards and OSB, composite under-tile seals , old paint coatings and old tile coverings,
- For use in dry and wet rooms (bathrooms, washrooms), on balconies, terraces, uninsulated and insulated facades, in water reservoirs, in basins and beaches of swimming pools, on floors exposed to high mechanical loads and stresses caused by temperature changes,
Possibility of installing cladding from small to large format inside and outside the building.
MAXIMUM PLATE SIZE AND APPLICATION:
INSIDE THE BUILDING
Floors - 120 cm x 120 cm,
Walls - 90 cm x 90 cm,
With heating - 60 cm x 60 cm,
OUTSIDE THE BUILDINGS
Floors - 60 cm x 60 cm,
Walls - 45 cm x 45 cm,
Without roof - 33 cm x 33 cm (light colors),
SUBSTRATE PREPARATION:
The substrate should be: even, compact, load-bearing, dry, durable, stable, free from dust and other substances that reduce adhesion. In case of large unevenness, level out using putties or self-leveling compounds:
- Rapid Concrete RC-20, RC-30,
- Self-leveling mortar ZS-014, ZSF-015,
Cementitious substrates with average absorbency do not require priming, only moistening with water to a matt-moist state. Avoid water ponding. Absorbent substrates: Before applying the adhesive, prepare the surfaces with one of Arsanit's primers.
TYPE OF SUBSTRATE AND PREPARATION:
Absorbent, inside, new - Acrylic Primer Stronger,
Absorbent, outdoor, old - HydroGrunt,
Wet zones, inside - Hydroisolator,
Wet areas, outdoors (balconies, terraces) - Hydroisolatro 1K, Hydroisolator 2K,
Glue PREPARATION:
Pour the appropriate amount of mixing water into a clean vessel. Pour the contents of the package and mix with an appropriate mixer (maximum 500 rpm) to obtain a homogeneous, lump-free, plastic mortar. Wait about 3 minutes and mix again.
Packaging Ceramik Ultra C2TE 25kg, mix in the following proportions:
- consistency that limits runoff (walls) - about 7 L of water / 25 kg bag,
- liquid consistency (floors) - about 8 liters of water / 25 kg bag,
Readiness time of the prepared mortar for work: approximately 4 hours, after this time the adhesive mortar cannot be reused by adding water or re-mixing with new glue.
EXECUTION:
- To obtain the best adhesion, first spread a thin contact layer on the substrate with the smooth side of the trowel.
- Then spread the adhesive mortar (possibly in one direction) onto the fresh contact layer using a suitable notched trowel. The selection of the trowel depends on the format of the tile and the evenness of the substrate. Use your fingertips to control the skinning time of the adhesive mortar.
- Place the tiles on the adhesive mortar with a slight sliding movement, press down and set in the right position.
- Ultra C2TE ceramics should be protected against water for 24 hours and frost and strong sunlight for 7 days after installation.
- If there are no other requirements, ensure that at least 75% of the tile surface is covered with adhesive mortar.
- On balconies, terraces, facades, underfloor and wall heating rooms, in swimming pools and swimming pools, and in the case of tile claddings subjected to high mechanical loads and in the case of gluing large-format tiles, it is required to stick at least 95% of the plate surface.
- Screeds with underfloor heating should be pre-heated before applying tile coverings.
- Apply only the amount of adhesive that can be covered with tiles during the open bonding time of 30 minutes.
- Tiles can be corrected for approximately 20 minutes after laying.
ATTENTION:
Work should be carried out in dry conditions, with air and substrate temperatures ranging from +5°C to +30°C. The applied mortar should be protected against frost, precipitation, direct sunlight and temperatures above +30°C for a period of approximately 2 weeks. The manufacturer is responsible for the quality of the product, but is not responsible for its specific applications. When using the product, comply with the provisions of this technical data sheet, building practice, relevant standards and occupational health and safety regulations. Information beyond the contents of this technical data sheet requires written confirmation from the manufacturer.
In case of doubts, contact the manufacturer's Technical Department.
STORAGE AND TRANSPORT:
Store the product in a dry room in original packaging, at a temperature from +5°C to +30°C. Protect from moisture.
The shelf life is 12 months from the production date indicated on the packaging.
PACKAGING:
25 kg, bag
PALETTE:
25 kg bags, pallet of 48 bags = 1200 kg
