THERMATYNK-SN is a silicone structural plaster intended for manual application of internal and external plasters. It can be used on all even and load-bearing surfaces, such as: concrete, cement, cement-lime walls, plaster walls, plasterboards, etc. THERMATYNK-SN can be applied to walls 28 days after their installation.
- for indoor and outdoor use,
- resistant to dirt,
- has self-cleaning properties,
- flexible and impact-resistant,
- waterproof,
- vapor permeable,
- bio-protective coating,
- microbiological protection,
- High color durability,
- available in a palette of 365 colors or dyed to individual order,
- an agent that accelerates setting and drying, we recommend SPRINTER-FT,
PROPERTIES:
THERMATYNK-SN - silicone plaster is a ready-to-use plaster with a paste consistency. It is efficient, convenient and easy to use. Silicone plaster creates a water vapor-permeable, hydrophobic coating, protected against the growth of fungi and algae - thanks to the innovative technology of active substances enclosed in capsules. It is characterized by high resistance to damage and weather conditions. The colors of THERMATYNK-SN silicone plasters are presented in the ARSANIT color palette, or colored according to our client's individual order.
IMPORTANT INFORMATION:
- Complete drying time: 12 to 48 hours,
- Initial drying time: about 15 minutes,
- Application temperature: from +5°C to +28°C,
- Shelf life: 12 months,
- For use: outdoor / indoor,
- Application method: manual,
PRODUCT PREPARATION:
THERMATYNK-SN - silicone plaster is offered in ready-made form and consistency. It must not be combined with other materials, thickened or diluted. After opening the bucket, mix the entire plaster thoroughly to obtain a uniform consistency.
AVAILABLE STRUCTURES AND GRIT SIZING:
Lamb 1.0 – 2.5 mm
Woodworm 1.5 – 2.5 mm
PREPARATION OF THE SUBSTRATE:
The substrate should be strong and even, clean of dirt, dust, grease, oil, wax, paint remnants, old paint and plaster coatings with insufficient adhesion should be removed, and any gaps should be filled using, for example, adhesive mortar. Before applying the plaster, regardless of the type of substrate, make a contact layer of THERMAGRUNT-SN primer to obtain an appropriate adhesive layer.
It is recommended to use a plaster primer in a color similar to the color of the plaster.
EXECUTION:
THERMATYNK-SN silicone plaster with the thickness of an aggregate grain should be applied to the prepared and primed substrate, using a smooth stainless steel trowel. Excess product should be drawn back into the bucket and mixed again. The obtained surface is smoothed using a plastic trowel.
- For plaster with a lamb-like structure - in circular motions.
- For plaster with a bark beetle structure - with vertical, horizontal or circular movements.
The time between applying and rubbing the plaster depends on the absorbency of the substrate, ambient temperature and consistency of the mortar. While plastering and drying, protect the plastered surface from sun, wind and rain. The test method should be used to determine the maximum plaster surface that can be applied in one technological cycle (application and smoothing) for the current weather conditions. The material should be applied without allowing the applied layer to dry before applying the next one. Otherwise, the junction of the two layers will be visible. Breaks in work should be planned appropriately (for example in the corners and bends of the building, under downspouts, at the junction of colors, etc.). The drying time of the plaster depends on the substrate, temperature and relative air humidity and ranges from 12 to 48 hours. In conditions of increased humidity and low temperature of approximately +5°C, the plaster setting time may be extended. During the application and drying of the THERMATYNK-SN silicone plaster, the ambient temperature should be +5°C to +28°C, also at night.
TOOLS:
Drill with mixer, smooth steel and plastic trowel. Tools should be washed with water immediately after work.
ATTENTION:
In order to avoid color differences when applying colored silicone plasters, plasters of the same date and production batch should be applied to one surface. Work should be carried out in accordance with the principles of construction practice and occupational health and safety regulations.
The shelf life is 12 months from the production date indicated on the packaging.
STORAGE AND TRANSPORT:
THERMATYNK-SN should be transported and stored in tightly closed buckets, at a positive temperature.
Protect from moisture.
PACKAGING:
Bucket 25 kg,
PALETTE:
25 kg x 24 pieces = 600 kg
