ARTE-TYNK nanoSN - silicone decorative structural plaster, intended for creating imitations of architectural concrete surfaces, smooth fine-grained plasters and other individually modeled structures. Designed for manual execution of internal and external plasters. It can be used on all even and load-bearing mineral substrates, such as cement, cement-lime plasters, concrete, etc. It can be applied to the wall 28 days after their application.
- has self-cleaning properties,
- for indoor and outdoor use,
- perfect imitation of architectural concrete,
- for imitation brick,
- flexible and impact-resistant,
- vapor permeable,
- microbiological protection,
- resistant to algae and fungi,
- attractive colors,
PROPERTIES:
ARTE-TYNK nanoSN nano-silicone plaster is a ready-to-use plaster with a paste consistency. It is efficient, convenient and easy to use. Silicone plaster creates a coating that is permeable to water vapor and, thanks to modern technology, protects against the development of algae and fungi. It is characterized by high resistance to damage and weather conditions. ARTE-TYNK-nanoSN is a surface plaster using modern technology with a fine-grained structure, for individual modeling. The colors of ARTE-TYNK nanoSN nano-silicone plasters are presented in the ARSANIT color palette. Other colors are also available upon customer request.
PREPARATION OF THE SUBSTRATE:
The substrate should be strong and even, free from dirt, dust, grease, oil, wax and paint remnants. Old paint and plaster coatings with insufficient adhesion should be removed and any gaps should be filled using adhesive mortar. Before applying the plaster, regardless of the type of substrate, make a contact layer of ARTE-GRUNT primer to obtain an appropriate adhesive layer. It is recommended to use a plaster primer in a color similar to the color of the plaster.
TOOLS:
Drill with mixer, smooth Venetian steel trowel and plastic trowel with bent corners, spiked rollers. Tools should be washed with water immediately after work.
PLASTER PREPARATION:
ARTE-TYNK nanoSN nano-silicone plaster is offered in ready-made form and consistency. It must not be combined with other materials, thickened or diluted. After opening the bucket, mix the entire plaster thoroughly to obtain a uniform consistency.
APPROXIMATE CONSUMPTION:
Structure 1.0 mm – 2.0 kg.m2
EXECUTION:
ARTE-TYNK nanoSN nano-silicone plaster with the thickness of the aggregate grain (layer thickness = grain thickness) should be applied to the prepared and primed substrate, using a smooth stainless steel trowel. In the case of architectural concrete, it is done in two layers: the first layer is applied with a thickness of about 1.0 mm, which after application should be stamped with a trowel or trowel. After this operation, the plaster should be left to dry for about 1 to 3 hours, depending on the air temperature and humidity. This structure can also be obtained with a paint roller, smoothing the fresh mass with it. The second layer, about 1 mm thick, after the plaster has dried slightly, start smoothing the plaster with a Venetian trowel (a trowel with a thicker and stiffer metal sheet). The pitting effect can be created without smoothing some places with a trowel - after prior application with a spiked roller. The thickness of the pits depends on the thickness of the applied plaster layer. After the layer has dried for 6-24 hours, the plaster can be additionally smoothed with a Venetian trowel. The traces of the anchors can be reflected in the fresh plaster, for example with a pipe. To make the plaster surface shiny, you can paint it with ARTE Fix-M. The mass is also suitable for applying other structures, for this purpose you can use rollers, stainless steel trowels, plastic trowels, as well as items such as a sponge, cloth, brush, spoon, bottle, etc. Protect during work and drying. against precipitation, too high temperature and strong wind. In conditions of increased humidity and low temperature of approximately +5°C, the plaster setting time may be extended. During the application and drying of the ARTE-TYNK nanoSN nano-silicone plaster, the ambient temperature should be +5°C to +28°C, also at night.
ATTENTION:
In order to avoid color differences when applying colored silicone plasters, plasters of the same date and production batch should be applied to one surface. Work should be carried out in accordance with the principles of construction practice.
STORAGE AND TRANSPORT:
Transport and store in tightly closed buckets, at a positive temperature. The shelf life is 12 months from the production date.
Protect from moisture.
PACKAGING:
Bucket 25 kg,
PALETTE:
25 kg x 24 pieces = 600 kg.
